Audio and video out of sync? Check your USB setup
When your camera and microphone are separate devices, each one takes its own time to deliver its signal, so sound and picture can arrive at slightly different moments. The most reliable fix is to take audio and video from the same device, for example a mic plugged into the camera. Otherwise keep both devices wired, off unpowered hubs and at the same sample rate, then check with a short test recording.
In short
- Separate camera and mic devices each add their own delay, so lips and voice can drift apart.
- Taking audio and video from one device, such as a mic plugged into the camera, keeps them together.
- Bluetooth microphones add a noticeable delay. Use a wired mic for live shows.
- Set your mic and other audio devices to the same sample rate, usually 48 kHz.
- Check sync with a clap at the start of a short test recording.
Why do audio and video drift apart?
A webcam and a USB microphone are two separate devices. Each one captures, converts and sends its signal through its own path, and video usually takes longer than sound because every frame has to be processed. When they come from different devices, your voice can arrive a little before your lips move.
The USB setup can make this worse. Every device plugged into a busy hub or controller competes with the others for bandwidth. A camera or capture card that is short of bandwidth buffers or drops frames, and the picture falls further behind the sound. Each device also has its own internal clock, and over a long show two clocks can drift apart a little.
You notice it most on close-up talking shots, which is exactly what most live shows are.
How do I keep audio and video together?
The best fix is to let one device carry both.
- Plug the mic into the camera. If your camera has a microphone input, connect your mic there. The camera keeps sound and picture together and sends them as one signal.
- With a capture card, use the card’s audio. A camera connected by HDMI sends its audio through the capture card. In evmux, choose the capture card’s own audio as the microphone for that camera.
- With a webcam and a separate mic, plug both straight into the computer, on ports that are not shared with other busy devices. Ports next to each other are often on the same controller. If you see drift, try other combinations of ports and test again.
Which USB and audio settings matter?
- Avoid unpowered hubs. Connect the camera and mic directly to the computer, or use a hub with its own power supply.
- Use wired audio. Bluetooth microphones and headsets add a delay you can see on camera, and many switch to lower quality audio while the mic is in use. Use a wired mic, and keep Bluetooth headphones for listening only.
- Match sample rates. Set your mic and audio interface to the same sample rate, 48 kHz, the usual rate for video. On a Mac, check it in Audio MIDI Setup. On Windows, open the device in the Sound settings and check its format.
- Use good cables. Damaged or very long USB cables cause dropouts that show up as stutter and drift.
- Keep the computer free. A computer struggling to draw the video drops frames, which looks like sync trouble. Lower the camera resolution and close other apps. A camera that freezes rather than drifts has a different cause, covered in camera freezes or glitches.
What should I check in evmux?
Sync is best fixed at the source, with the steps above. In the studio, these settings help you avoid related problems:
- Pick the right microphone. Open Settings with the gear in the bottom toolbar and choose your microphone under Audio. For an extra camera, choose its microphone in that camera’s tab under Settings, then Camera, in the Audio Source list.
- Do not use one mic twice. If two cameras on the same scene use the same microphone, viewers hear it doubled. Give each camera its own mic, or No Audio.
- Know your processing. Echo cancellation, noise suppression and auto gain control are on by default. AI noise reduction is a separate option, and it should not run together with echo cancellation, because the two filters compete. See live stream audio.
- Expect a small offset on screen share audio. Sound that comes in with a screen share arrives slightly later than your camera, so your lips may not match it exactly.
How do I test for sync?
- In evmux, switch every destination off, so the button reads Record instead of Go Live. Tick Recording and start. See recording.
- Look into the camera and clap your hands once, clearly in frame. Then talk for a minute.
- Stop, download the recording and watch it. The sound of the clap should land on the frame where your hands meet.
- If the sound comes first, the video path is slower. Lower the camera resolution, move the camera to another port, or take the audio from the camera.
- Change one thing at a time and record again, so you know what fixed it.
If you only need to check how your mic sounds, the Test audio panel in the audio settings records a 5-second clip and plays it back.